1. NAME

xorg.conf and xorg.conf.d - configuration files for Xorg X server

2. INTRODUCTION

Xorg supports several mechanisms for supplying/obtaining configuration and run-time parameters: command line options, environment variables, the xorg.conf and xorg.conf.d configuration files, auto-detection, and fallback defaults. When the same information is supplied in more than one way, the highest precedence mechanism is used. The list of mechanisms is ordered from highest precedence to lowest. Note that not all parameters can be supplied via all methods. The available command line options and environment variables (and some defaults) are described in the Xserver(1) and Xorg(1) manual pages. Most configuration file parameters, with their defaults, are described below. Driver and module specific configuration parameters are described in the relevant driver or module manual page.

3. DESCRIPTION

Xorg uses a configuration file called xorg.confand files ending in the suffix .conffrom the directory xorg.conf.dfor its initial setup. The xorg.confconfiguration file is searched for in the following places when the server is started as a normal user:

   .nf /etc/X11/ <cmdline> /usr/etc/X11/ <cmdline> .IB /etc/X11/ $XORGCONFIG .IB /usr/etc/X11/ $XORGCONFIG /etc/X11/xorg.conf-4 /etc/X11/xorg.conf /etc/xorg.conf /usr/etc/X11/xorg.conf. <hostname> /usr/etc/X11/xorg.conf-4 /usr/etc/X11/xorg.conf /usr/lib/X11/xorg.conf. <hostname> /usr/lib/X11/xorg.conf-4 /usr/lib/X11/xorg.conf

where <cmdline>is a relative path (with no « .. » components) specified with the

-config command line option,

$XORGCONFIG is the relative path (with no « .. » components) specified by that environment variable, and <hostname>is the machine's hostname as reported by

R gethostname (3).

When the Xorg server is started by the « root » user, the config file search locations are as follows:


    .nf <cmdline> /etc/X11/ <cmdline> /usr/etc/X11/ <cmdline>

$XORGCONFIG .IB /etc/X11/ $XORGCONFIG .IB /usr/etc/X11/ $XORGCONFIG /etc/X11/xorg.conf-4 /etc/X11/xorg.conf /etc/xorg.conf /usr/etc/X11/xorg.conf. <hostname> /usr/etc/X11/xorg.conf-4 /usr/etc/X11/xorg.conf /usr/lib/X11/xorg.conf. <hostname> /usr/lib/X11/xorg.conf-4 /usr/lib/X11/xorg.conf

where <cmdline>is the path specified with the

-config command line option (which may be absolute or relative),

$XORGCONFIG is the path specified by that environment variable (absolute or relative),

$HOME is the path specified by that environment variable (usually the home directory), and <hostname>is the machine's hostname as reported by

R gethostname (3).

Additional configuration files are searched for in the following directories when the server is started as a normal user:

   .nf /etc/X11/ <cmdline> /etc/X11/ <cmdline> /etc/X11/xorg.conf.d /etc/X11/xorg.conf.d

where <cmdline>is a relative path (with no « .. » components) specified with the

-configdir command line option.

When the Xorg server is started by the « root » user, the config directory search locations are as follows:

   .nf <cmdline> /etc/X11/ <cmdline> /etc/X11/ <cmdline> /etc/X11/xorg.conf.d /etc/X11/xorg.conf.d

where <cmdline>is the path specified with the

-configdir command line option (which may be absolute or relative).

Finally, configuration files will also be searched for in directories reserved for system use. These are to separate configuration files from the vendor or 3rd party packages from those of local administration. These files are found in the following directories:

   .nf /usr/share/X11/xorg.conf.d /usr/share/X11/xorg.conf.d

The xorg.confand xorg.conf.dfiles are composed of a number of sections which may be present in any order, or omitted to use default configuration values. Each section has the form:


    .nf Section \*q SectionName \*q " " SectionEntry ...

EndSection

The section names are:


    .nf

R

R

R

R

R

R

R

R

R

R

R

R

R

R

The following obsolete section names are still recognised for compatibility purposes. In new config files, the

InputDevice section should be used instead.


    .nf

R

R

The old

XInput section is no longer recognised.

The

ServerLayout sections are at the highest level. They bind together the input and output devices that will be used in a session. The input devices are described in the

InputDevice sections. Output devices usually consist of multiple independent components (e.g., a graphics board and a monitor). These multiple components are bound together in the

Screen sections, and it is these that are referenced by the

ServerLayout section. Each

Screen section binds together a graphics board and a monitor. The graphics boards are described in the

Device sections, and the monitors are described in the

Monitor sections.

Config file keywords are case-insensitive, and « _ » characters are ignored. Most strings (including

Option names) are also case-insensitive, and insensitive to white space and « _ » characters.

Each config file entry usually takes up a single line in the file. They consist of a keyword, which is possibly followed by one or more arguments, with the number and types of the arguments depending on the keyword. The argument types are:


    .nf

R

R

R

Note: hex integer values must be prefixed with « 0x », and octal values with « 0 ».

A special keyword called

Option may be used to provide free-form data to various components of the server. The

Option keyword takes either one or two string arguments. The first is the option name, and the optional second argument is the option value. Some commonly used option value types include:


    .nf

R

R

R

R

R

Note that all

Option values, not just strings, must be enclosed in quotes.

Boolean options may optionally have a value specified. When no value is specified, the option's value is

R TRUE . The following boolean option values are recognised as

R TRUE :


    .BR 1 ,

R on ,

R true ,

yes

and the following boolean option values are recognised as

R FALSE :


    .BR 0 ,

R off ,

R false ,

no

If an option name is prefixed with \*q No \*q, then the option value is negated.

Example: the following option entries are equivalent:


    .nf

Option \*qAccel\*q \*qOff\*q

Option \*qNoAccel\*q

Option \*qNoAccel\*q \*qOn\*q

Option \*qAccel\*q \*qfalse\*q

Option \*qAccel\*q \*qno\*q

Frequency option values consist of a real number that is optionally followed by one of the following frequency units:


    .BR Hz ,

R k ,

R kHz ,

R M ,

MHz

When the unit name is omitted, the correct units will be determined from the value and the expectations of the appropriate range of the value. It is recommended that the units always be specified when using frequency option values to avoid any errors in determining the value.

4. FILES SECTION

The

Files section is used to specify some path names required by the server. Some of these paths can also be set from the command line (see

R Xserver (1) and

R Xorg (1)). The command line settings override the values specified in the config file. The

Files section is optional, as are all of the entries that may appear in it.

The entries that can appear in this section are:

  • FontPath \*q path \*q
           sets the search path for fonts. This path is a comma separated list of font path elements which the Xorg server searches for font databases. Multiple

FontPath entries may be specified, and they will be concatenated to build up the fontpath used by the server. Font path elements can be absolute directory paths, catalogue directories or a font server identifier. The formats of the later two are explained below:


       Catalogue directories:


    Catalogue directories can be specified using the prefix catalogue: before the directory name. The directory can then be populated with symlinks pointing to the real font directories, using the following syntax in the symlink name:


     <identifier> : [attribute]: pri= <priority>

where <identifier>is an alphanumeric identifier, [attribute]is an attribute which will be passed to the underlying FPE and <priority>is a number used to order the fontfile FPEs. Examples:

   .nf 75dpi:unscaled:pri=20 -> /usr/share/X11/fonts/75dpi gscript:pri=60 -> /usr/share/fonts/default/ghostscript misc:unscaled:pri=10 -> /usr/share/X11/fonts/misc


       Font server identifiers:


    Font server identifiers have the form:
    .PP <trans> / <hostname> : <port-number>

where <trans>is the transport type to use to connect to the font server (e.g.,

unix for UNIX-domain sockets or

tcp for a TCP/IP connection), <hostname>is the hostname of the machine running the font server, and <port-number>is the port number that the font server is listening on (usually 7100).

When this entry is not specified in the config file, the server falls back to the compiled-in default font path, which contains the following font path elements (which can be set inside a catalogue directory):

   .nf /usr/lib/X11/fonts/misc/ /usr/lib/X11/fonts/TTF/ /usr/lib/X11/fonts/OTF/ /usr/lib/X11/fonts/Type1/ /usr/lib/X11/fonts/100dpi/ /usr/lib/X11/fonts/75dpi/

Font path elements that are found to be invalid are removed from the font path when the server starts up.

  • ModulePath \*q path \*q
           sets the search path for loadable Xorg server modules. This path is a comma separated list of directories which the Xorg server searches for loadable modules loading in the order specified. Multiple

ModulePath entries may be specified, and they will be concatenated to build the module search path used by the server. The default module path is


           /usr/lib/xorg/modules .ig

  • LogFile \*q path \*q
           sets the name of the Xorg server log file. The default log file name is


            /var/log/Xorg. <n> .log


       where <n>is the display number for the Xorg server.

  • XkbDir \*q path \*q
           sets the base directory for keyboard layout files. The

-xkbdir command line option can be used to override this. The default directory is


           /usr/share/X11/xkb

5. SERVERFLAGS SECTION

In addition to options specific to this section (described below), the

ServerFlags section is used to specify some global Xorg server options. All of the entries in this section are

R Options , although for compatibility purposes some of the old style entries are still recognised. Those old style entries are not documented here, and using them is discouraged. The

ServerFlags section is optional, as are the entries that may be specified in it.

Options specified in this section (with the exception of the

\*qDefaultServerLayout\*q

R Option ) may be overridden by

Options specified in the active

ServerLayout section. Options with command line equivalents are overridden when their command line equivalent is used. The options recognised by this section are:

  • Option \*qDefaultServerLayout\*q \*q layout-id \*q
           This specifies the default

ServerLayout section to use in the absence of the

-layout command line option.

  • Option \*qNoTrapSignals\*q \*q boolean \*q
           This prevents the Xorg server from trapping a range of unexpected fatal signals and exiting cleanly. Instead, the Xorg server will die and drop core where the fault occurred. The default behaviour is for the Xorg server to exit cleanly, but still drop a core file. In general you never want to use this option unless you are debugging an Xorg server problem and know how to deal with the consequences.
  • Option \*qUseSIGIO\*q \*q boolean \*q
           This controls whether the Xorg server requests that events from input devices be reported via a SIGIO signal handler (also known as SIGPOLL on some platforms), or only reported via the standard select(3) loop. The default behaviour is platform specific. In general you do not want to use this option unless you are debugging the Xorg server, or working around a specific bug until it is fixed, and understand the consequences.
  • Option \*qDontVTSwitch\*q \*q boolean \*q
           This disallows the use of the Ctrl+Alt+F n sequence (where F n refers to one of the numbered function keys). That sequence is normally used to switch to another \*qvirtual terminal\*q on operating systems that have this feature. When this option is enabled, that key sequence has no special meaning and is passed to clients. Default: off.
  • Option \*qDontZap\*q \*q boolean \*q
           This disallows the use of the

Terminate_Server XKB action (usually on Ctrl+Alt+Backspace, depending on XKB options). This action is normally used to terminate the Xorg server. When this option is enabled, the action has no effect. Default: off.

  • Option \*qDontZoom\*q \*q boolean \*q
           This disallows the use of the

Ctrl+Alt+Keypad-Plus and

Ctrl+Alt+Keypad-Minus sequences. These sequences allows you to switch between video modes. When this option is enabled, those key sequences have no special meaning and are passed to clients. Default: off.

  • Option \*qDisableVidModeExtension\*q \*q boolean \*q
           This disables the parts of the VidMode extension used by the xvidtune client that can be used to change the video modes. Default: the VidMode extension is enabled.
  • Option \*qAllowNonLocalXvidtune\*q \*q boolean \*q
           This allows the xvidtune client (and other clients that use the VidMode extension) to connect from another host. Default: off.
  • Option \*qAllowMouseOpenFail\*q \*q boolean \*q
           This tells the mousedrv(4) and vmmouse(4) drivers to not report failure if the mouse device can't be opened/initialised. It has no effect on the evdev(4) or other drivers. The previous functionality of allowing the server to start up even if the mouse device can't be opened/initialised is now handled by the AllowEmptyInput option. Default: false.
  • Option \*qVTSysReq\*q \*q boolean \*q
           enables the SYSV-style VT switch sequence for non-SYSV systems which support VT switching. This sequence is

Alt-SysRq followed by a function key ( Fn ). This prevents the Xorg server trapping the keys used for the default VT switch sequence, which means that clients can access them. Default: off.

  • Option \*qBlankTime\*q \*q time \*q
           sets the inactivity timeout for the

blank phase of the screensaver. timeis in minutes. This is equivalent to the Xorg server's

-s flag, and the value can be changed at run-time with

R xset(1). Default: 10 minutes.

  • Option \*qStandbyTime\*q \*q time \*q
           sets the inactivity timeout for the

standby phase of DPMS mode. timeis in minutes, and the value can be changed at run-time with

R xset(1). Default: 10 minutes. This is only suitable for VESA DPMS compatible monitors, and may not be supported by all video drivers. It is only enabled for screens that have the

\*qDPMS\*q option set (see the MONITOR section below).

  • Option \*qSuspendTime\*q \*q time \*q
           sets the inactivity timeout for the

suspend phase of DPMS mode. timeis in minutes, and the value can be changed at run-time with

R xset(1). Default: 10 minutes. This is only suitable for VESA DPMS compatible monitors, and may not be supported by all video drivers. It is only enabled for screens that have the

\*qDPMS\*q option set (see the MONITOR section below).

  • Option \*qOffTime\*q \*q time \*q
           sets the inactivity timeout for the

off phase of DPMS mode. timeis in minutes, and the value can be changed at run-time with

R xset(1). Default: 10 minutes. This is only suitable for VESA DPMS compatible monitors, and may not be supported by all video drivers. It is only enabled for screens that have the

\*qDPMS\*q option set (see the MONITOR section below).

  • Option \*qPixmap\*q \*q bpp \*q
           This sets the pixmap format to use for depth 24. Allowed values for bppare 24 and 32. Default: 32 unless driver constraints don't allow this (which is rare). Note: some clients don't behave well when this value is set to 24.
  • Option \*qPC98\*q \*q boolean \*q
           Specify that the machine is a Japanese PC-98 machine. This should not be enabled for anything other than the Japanese-specific PC-98 architecture. Default: auto-detected.
  • Option \*qNoPM\*q \*q boolean \*q
           Disables something to do with power management events. Default: PM enabled on platforms that support it.
  • Option \*qXinerama\*q \*q boolean \*q
           enable or disable XINERAMA extension. Default is disabled.
  • Option \*qAIGLX\*q \*q boolean \*q
           enable or disable AIGLX. AIGLX is enabled by default.
  • Option \*qDRI2\*q \*q boolean \*q
           enable or disable DRI2. DRI2 is disabled by default.
  • Option \*qGlxVisuals\*q \*q string \*q
           This option controls how many GLX visuals the GLX modules sets up. The default value is

R which will setup up a typical subset of the GLXFBConfigs provided by the driver as GLX visuals. Other options are

R which will set up the minimal set allowed by the GLX specification and

R which will setup GLX visuals for all GLXFBConfigs.

  • Option \*qUseDefaultFontPath\*q \*q boolean \*q
           Include the default font path even if other paths are specified in xorg.conf. If enabled, other font paths are included as well. Enabled by default.
  • Option \*qIgnoreABI\*q \*q boolean \*q
           Allow modules built for a different, potentially incompatible version of the X server to load. Disabled by default.
  • Option \*qAllowEmptyInput\*q \*q boolean \*q
           If enabled, don't add the standard keyboard and mouse drivers, if there are no input devices in the config file. Enabled by default if AutoAddDevices and AutoEnableDevices is enabled, otherwise disabled. If AllowEmptyInput is on, devices using the kbd, mouse or vmmouse driver are ignored.
  • Option \*qAutoAddDevices\*q \*q boolean \*q
           If this option is disabled, then no devices will be added from HAL events. Enabled by default.
  • Option \*qAutoEnableDevices\*q \*q boolean \*q
           If this option is disabled, then the devices will be added (and the DevicePresenceNotify event sent), but not enabled, thus leaving policy up to the client. Enabled by default.
  • Option \*qLog\*q \*q string \*q
           This option controls whether the log is flushed and/or synced to disk after each message. Possible values are

flush or

R sync . Unset by default.

6. MODULE SECTION

The

Module section is used to specify which Xorg server modules should be loaded. This section is ignored when the Xorg server is built in static form. The type of modules normally loaded in this section are Xorg server extension modules. Most other module types are loaded automatically when they are needed via other mechanisms. The

Module section is optional, as are all of the entries that may be specified in it.

Entries in this section may be in two forms. The first and most commonly used form is an entry that uses the

Load keyword, as described here:

  • Load \*q modulename \*q
           This instructs the server to load the module called modulename . The module name given should be the module's standard name, not the module file name. The standard name is case-sensitive, and does not include the « lib » prefix, or the « .a », « .o », or « .so » suffixes.


       Example: the DRI extension module can be loaded with the following entry:


    .B "Load \*qdri\*q"

  • Disable \*q modulename \*q
           This instructs the server to not load the module called modulename . Some modules are loaded by default in the server, and this overrides that default. If a

Load instruction is given for the same module, it overrides the

Disable instruction and the module is loaded. The module name given should be the module's standard name, not the module file name. As with the

Load instruction, the standard name is case-sensitive, and does not include the "lib" prefix, or the ".a", ".o", or ".so" suffixes.

The second form of entry is a

R SubSection, with the subsection name being the module name, and the contents of the

SubSection being

Options that are passed to the module when it is loaded.

Example: the extmod module (which contains a miscellaneous group of server extensions) can be loaded, with the XFree86-DGA extension disabled by using the following entry:


    .nf

SubSection \*qextmod\*q

Option \*qomit XFree86-DGA\*q

EndSubSection

Modules are searched for in each directory specified in the

ModulePath search path, and in the drivers, extensions, input, internal, and multimedia subdirectories of each of those directories. In addition to this, operating system specific subdirectories of all the above are searched first if they exist.

To see what extension modules are available, check the extensions subdirectory under:

   .nf /usr/lib/xorg/modules

The « extmod », « dbe », « dri », « dri2 », « glx », and « record » extension modules are loaded automatically, if they are present, unless disabled with \*qDisable\*q entries. It is recommended that at very least the « extmod » extension module be loaded. If it isn't, some commonly used server extensions (like the SHAPE extension) will not be available.

7. EXTENSIONS SECTION

The

Extensions section is used to specify which X11 protocol extensions should be enabled or disabled. The

Extensions section is optional, as are all of the entries that may be specified in it.

Entries in this section are listed as Option statements with the name of the extension as the first argument, and a boolean value as the second. The extension name is case-sensitive, and matches the form shown in the output of \*qXorg -extension ?\*q.


       Example: the MIT-SHM extension can be disabled with the following entry:


    .nf

Section \*qExtensions\*q

Option \*qMIT-SHM\*q \*qDisable\*q

EndSection

8. INPUTDEVICE SECTION

The config file may have multiple

InputDevice sections. Recent X servers employ input hotplugging to add input devices, with the HAL backend being the default backend for X servers since 1.4. It is usually not necessary to provide

InputDevice sections in the xorg.conf if hotplugging is enabled.

If hotplugging is disabled, there will normally be at least two: one for the core (primary) keyboard and one for the core pointer. If either of these two is missing, a default configuration for the missing ones will be used. In the absence of an explicitly specified core input device, the first

InputDevice marked as

CorePointer (or

R CoreKeyboard ) is used. If there is no match there, the first

InputDevice that uses the « mouse » (or « kbd ») driver is used. The final fallback is to use built-in default configurations. Currently the default configuration may not work as expected on all platforms.

InputDevice sections have the following format:


    .nf

Section \*qInputDevice\*q Identifier \*q name \*q Driver \*q inputdriver \*q options"..."

EndSection

The

Identifier and

Driver entries are required in all

InputDevice sections. All other entries are optional.

The

Identifier entry specifies the unique name for this input device. The

Driver entry specifies the name of the driver to use for this input device. When using the loadable server, the input driver module \*q inputdriver \*q will be loaded for each active

InputDevice section. An

InputDevice section is considered active if it is referenced by an active

ServerLayout section, if it is referenced by the

-keyboard or

-pointer command line options, or if it is selected implicitly as the core pointer or keyboard device in the absence of such explicit references. The most commonly used input drivers are

R evdev (4) on Linux systems, and

R kbd (4) and

R mousedrv (4) on other platforms.

InputDevice sections recognise some driver-independent

R Options , which are described here. See the individual input driver manual pages for a description of the device-specific options.

  • Option \*qAutoServerLayout\*q \*q boolean \*q
           Always add the device to the ServerLayout section used by this instance of the server. This affects implied layouts as well as explicit layouts specified in the configuration and/or on the command line.
  • Option \*qCorePointer\*q
           Deprecated, use

SendCoreEvents instead.

  • Option \*qCoreKeyboard\*q
           Deprecated, use

SendCoreEvents instead.

  • Option \*qAlwaysCore\*q \*q boolean \*q
           .B Deprecated, use

SendCoreEvents instead.

  • Option \*qSendCoreEvents\*q \*q boolean \*q
           Both of these options are equivalent, and when enabled cause the input device to report core events through the master device. They are enabled by default. Any device configured to send core events will be attached to the virtual core pointer or keyboard and control the cursor by default. Devices with

SendCoreEvents disabled will be \*qfloating\*q and only accessible by clients employing the X Input extension. This option controls the startup behavior only, a device may be reattached or set floating at runtime.

  • Option \*qSendDragEvents\*q \*q boolean \*q
           Send core events while dragging. Enabled by default.

For pointing devices, the following options control how the pointer is accelerated or decelerated with respect to physical device motion. Most of these can be adjusted at runtime, see the xinput(1) man page for details. Only the most important acceleration options are discussed here.

  • Option \*qAccelerationProfile\*q \*q integer \*q
           Select the profile. In layman's terms, the profile constitutes the "feeling" of the acceleration. More formally, it defines how the transfer function (actual acceleration as a function of current device velocity and acceleration controls) is constructed. This is mainly a matter of personal preference.


      .nf

0 classic (mostly compatible)

-1 none (only constant deceleration is applied)

1 device-dependent

2 polynomial (polynomial function)

3 smooth linear (soft knee, then linear)

4 simple (normal when slow, otherwise accelerated)

5 power (power function)

6 linear (more speed, more acceleration)

  • Option \*qConstantDeceleration\*q \*q real \*q
           Makes the pointer go

deceleration times slower than normal. Most useful for high-resolution devices.

  • Option \*qAdaptiveDeceleration\*q \*q real \*q
           Allows to actually decelerate the pointer when going slow. At most, it will be

adaptive deceleration times slower. Enables precise pointer placement without sacrificing speed.

  • Option \*qAccelerationScheme\*q \*q string \*q
           Selects the scheme, which is the underlying algorithm.


       .nf

predictable default algorithm (behaving more predictable)

lightweight old acceleration code (as specified in the X protocol spec)

none no acceleration or deceleration

  • Option \*qAccelerationNumerator\*q \*q integer \*q
  • Option \*qAccelerationDenominator\*q \*q integer \*q
           Set numerator and denominator of the acceleration factor. The acceleration factor is a rational which, together with threshold, can be used to tweak profiles to suit the users needs. The

simple and

limited profiles use it directly (i.e. they accelerate by the factor), for other profiles it should hold that a higher acceleration factor leads to a faster pointer. Typically, 1 is unaccelerated and values up to 5 are sensible.

  • Option \*qAccelerationThreshold\*q \*q integer \*q
           Set the threshold, which is roughly the velocity (usually device units per 10 ms) required for acceleration to become effective. The precise effect varies with the profile however.

9. INPUTCLASS SECTION

The config file may have multiple

InputClass sections. These sections are optional and are used to provide configuration for a class of input devices as they are automatically added. An input device can match more than one

InputClass section. Each class can override settings from a previous class, so it is best to arrange the sections with the most generic matches first.

InputClass sections have the following format:


    .nf

Section \*qInputClass\*q Identifier \*q name \*q entries"..."options"..."

EndSection

The

Identifier entry is required in all

InputClass sections. All other entries are optional.

The

Identifier entry specifies the unique name for this input class. The

Driver entry specifies the name of the driver to use for this input device. After all classes have been examined, the \*q inputdriver \*q module from the first

Driver entry will be enabled when using the loadable server.

When an input device is automatically added, its characteristics are checked against all

InputClass sections. Each section can contain optional entries to narrow the match of the class. If none of the optional entries appear, the

InputClass section is generic and will match any input device. If more than one of these entries appear, they all must match for the configuration to apply. The allowed matching entries are shown below.

  • MatchProduct \*q matchproduct \*q
           This entry can be used to check if the substring \*q matchproduct \*q occurs in the device's product name. Multiple substrings can be matched by separating arguments with a '|' character.
  • MatchVendor \*q matchvendor \*q
           This entry can be used to check if the substring \*q matchvendor \*q occurs in the device's vendor name. Multiple substrings can be matched by separating arguments with a '|' character.
  • MatchDevicePath \*q matchdevice \*q
           This entry can be used to check if the device file matches the \*q matchdevice \*q pathname pattern. Multiple patterns can be matched by separating arguments with a '|' character.
  • MatchTag \*q matchtag \*q
           This entry can be used to check if tags assigned by the config backend matches the \*q matchtag \*q pattern. Multiple patterns can be matched by separating arguments with a '|' character. A match is found if at least one of the tags given in \*q matchtag \*q matches at least one of the tags assigned by the backend.
  • MatchIsKeyboard \*q bool \*q
  • MatchIsPointer \*q bool \*q
  • MatchIsJoystick \*q bool \*q
  • MatchIsTablet \*q bool \*q
  • MatchIsTouchpad \*q bool \*q
  • MatchIsTouchscreen \*q bool \*q
           Match device types. These entries take a boolean argument similar to

Option entries.

When an input device has been matched to the

InputClass section, any

Option entries are applied to the device. One

InputClass specific

Option is recognized. See the

InputDevice section above for a description of the remaining

Option entries.

  • Option \*qIgnore\*q \*q boolean \*q
           This optional entry specifies that the device should be ignored entirely, and not added to the server. This can be useful when the device is handled by another program and no X events should be generated.

10. DEVICE SECTION

The config file may have multiple

Device sections. There must be at least one, for the video card being used.

Device sections have the following format:


    .nf

Section \*qDevice\*q Identifier \*q name \*q Driver \*q driver \*q entries"..."

EndSection

The

Identifier and

Driver entries are required in all

Device sections. All other entries are optional.

The

Identifier entry specifies the unique name for this graphics device. The

Driver entry specifies the name of the driver to use for this graphics device. When using the loadable server, the driver module \*q driver \*q will be loaded for each active

Device section. A

Device section is considered active if it is referenced by an active

Screen section.

Device sections recognise some driver-independent entries and

R Options , which are described here. Not all drivers make use of these driver-independent entries, and many of those that do don't require them to be specified because the information is auto-detected. See the individual graphics driver manual pages for further information about this, and for a description of the device-specific options. Note that most of the

Options listed here (but not the other entries) may be specified in the

Screen section instead of here in the

Device section.

  • BusID \*q bus-id \*q
           This specifies the bus location of the graphics card. For PCI/AGP cards, the bus-idstring has the form PCI: bus : device : function (e.g., « PCI:1:0:0 » might be appropriate for an AGP card). This field is usually optional in single-head configurations when using the primary graphics card. In multi-head configurations, or when using a secondary graphics card in a single-head configuration, this entry is mandatory. Its main purpose is to make an unambiguous connection between the device section and the hardware it is representing. This information can usually be found by running the pciaccess tool scanpci.
  • Screen number
           This option is mandatory for cards where a single PCI entity can drive more than one display (i.e., multiple CRTCs sharing a single graphics accelerator and video memory). One

Device section is required for each head, and this parameter determines which head each of the

Device sections applies to. The legal values of numberrange from 0 to one less than the total number of heads per entity. Most drivers require that the primary screen (0) be present.

  • Chipset \*q chipset \*q
           This usually optional entry specifies the chipset used on the graphics board. In most cases this entry is not required because the drivers will probe the hardware to determine the chipset type. Don't specify it unless the driver-specific documentation recommends that you do.
  • Ramdac \*q ramdac-type \*q
           This optional entry specifies the type of RAMDAC used on the graphics board. This is only used by a few of the drivers, and in most cases it is not required because the drivers will probe the hardware to determine the RAMDAC type where possible. Don't specify it unless the driver-specific documentation recommends that you do.
  • DacSpeed speed
  • DacSpeed speed-8 speed-16 speed-24 speed-32
           This optional entry specifies the RAMDAC speed rating (which is usually printed on the RAMDAC chip). The speed is in MHz. When one value is given, it applies to all framebuffer pixel sizes. When multiple values are given, they apply to the framebuffer pixel sizes 8, 16, 24 and 32 respectively. This is not used by many drivers, and only needs to be specified when the speed rating of the RAMDAC is different from the defaults built in to driver, or when the driver can't auto-detect the correct defaults. Don't specify it unless the driver-specific documentation recommends that you do.
  • Clocks clock ...
           specifies the pixel that are on your graphics board. The clocks are in MHz, and may be specified as a floating point number. The value is stored internally to the nearest kHz. The ordering of the clocks is important. It must match the order in which they are selected on the graphics board. Multiple

Clocks lines may be specified, and each is concatenated to form the list. Most drivers do not use this entry, and it is only required for some older boards with non-programmable clocks. Don't specify this entry unless the driver-specific documentation explicitly recommends that you do.

  • ClockChip \*q clockchip-type \*q
        This optional entry is used to specify the clock chip type on graphics boards which have a programmable clock generator. Only a few Xorg drivers support programmable clock chips. For details, see the appropriate driver manual page.
  • VideoRam mem
           This optional entry specifies the amount of video ram that is installed on the graphics board. This is measured in kBytes. In most cases this is not required because the Xorg server probes the graphics board to determine this quantity. The driver-specific documentation should indicate when it might be needed.
  • BiosBase baseaddress
           This optional entry specifies the base address of the video BIOS for the VGA board. This address is normally auto-detected, and should only be specified if the driver-specific documentation recommends it.
  • MemBase baseaddress
           This optional entry specifies the memory base address of a graphics board's linear frame buffer. This entry is not used by many drivers, and it should only be specified if the driver-specific documentation recommends it.
  • IOBase baseaddress
           This optional entry specifies the IO base address. This entry is not used by many drivers, and it should only be specified if the driver-specific documentation recommends it.
  • ChipID id
           This optional entry specifies a numerical ID representing the chip type. For PCI cards, it is usually the device ID. This can be used to override the auto-detection, but that should only be done when the driver-specific documentation recommends it.
  • ChipRev rev
           This optional entry specifies the chip revision number. This can be used to override the auto-detection, but that should only be done when the driver-specific documentation recommends it.
  • TextClockFreq freq
           This optional entry specifies the pixel clock frequency that is used for the regular text mode. The frequency is specified in MHz. This is rarely used.
  • Option \*qModeDebug\*q \*q boolean \*q
           Enable printing of additional debugging information about modesetting to the server log. .ig
  • This optional entry allows an IRQ number to be specified.

Options

       Option flags may be specified in the

Device sections. These include driver-specific options and driver-independent options. The former are described in the driver-specific documentation. Some of the latter are described below in the section about the

Screen section, and they may also be included here.

11. VIDEOADAPTOR SECTION

Nobody wants to say how this works. Maybe nobody knows ...

12. MONITOR SECTION

The config file may have multiple

Monitor sections. There should normally be at least one, for the monitor being used, but a default configuration will be created when one isn't specified.

Monitor sections have the following format:


    .nf

Section \*qMonitor\*q Identifier \*q name \*q entries"..."

EndSection

The only mandatory entry in a

Monitor section is the

Identifier entry.

The

Identifier entry specifies the unique name for this monitor. The

Monitor section may be used to provide information about the specifications of the monitor, monitor-specific

R Options , and information about the video modes to use with the monitor.

With RandR 1.2-enabled drivers, monitor sections may be tied to specific outputs of the video card. Using the name of the output defined by the video driver plus the identifier of a monitor section, one associates a monitor section with an output by adding an option to the Device section in the following format:

Option \*qMonitor-outputname\*q \*qmonitorsection\*q (for example,

Option \*qMonitor-VGA\*q \*qVGA monitor\*q for a VGA output)

In the absence of specific association of monitor sections to outputs, if a monitor section is present the server will associate it with an output to preserve compatibility for previous single-head configurations.

Specifying video modes is optional because the server will use the DDC or other information provided by the monitor to automatically configure the list of modes available. When modes are specified explicitly in the

Monitor section (with the

R Modes ,

R ModeLine , or

UseModes keywords), built-in modes with the same names are not included. Built-in modes with different names are, however, still implicitly included, when they meet the requirements of the monitor.

The entries that may be used in

Monitor sections are described below.

  • VendorName \*q vendor \*q
           This optional entry specifies the monitor's manufacturer.
  • ModelName \*q model \*q
           This optional entry specifies the monitor's model.
  • HorizSync horizsync-range
           gives the range(s) of horizontal sync frequencies supported by the monitor. horizsync-rangemay be a comma separated list of either discrete values or ranges of values. A range of values is two values separated by a dash. By default the values are in units of kHz. They may be specified in MHz or Hz if

MHz or

Hz is added to the end of the line. The data given here is used by the Xorg server to determine if video modes are within the specifications of the monitor. This information should be available in the monitor's handbook. If this entry is omitted, a default range of 28-33kHz is used.

  • VertRefresh vertrefresh-range
           gives the range(s) of vertical refresh frequencies supported by the monitor. vertrefresh-rangemay be a comma separated list of either discrete values or ranges of values. A range of values is two values separated by a dash. By default the values are in units of Hz. They may be specified in MHz or kHz if

MHz or

kHz is added to the end of the line. The data given here is used by the Xorg server to determine if video modes are within the specifications of the monitor. This information should be available in the monitor's handbook. If this entry is omitted, a default range of 43-72Hz is used.

  • DisplaySize width height
           This optional entry gives the width and height, in millimetres, of the picture area of the monitor. If given this is used to calculate the horizontal and vertical pitch (DPI) of the screen.
  • Gamma gamma-value
  • Gamma red-gamma green-gamma blue-gamma
           This is an optional entry that can be used to specify the gamma correction for the monitor. It may be specified as either a single value or as three separate RGB values. The values should be in the range 0.1 to 10.0, and the default is 1.0. Not all drivers are capable of using this information.
  • UseModes \*q modesection-id \*q
           Include the set of modes listed in the

Modes section called modesection-id. This makes all of the modes defined in that section available for use by this monitor.

  • Mode \*q name \*q
           This is an optional multi-line entry that can be used to provide definitions for video modes for the monitor. In most cases this isn't necessary because the built-in set of VESA standard modes will be sufficient. The

Mode keyword indicates the start of a multi-line video mode description. The mode description is terminated with the

EndMode keyword. The mode description consists of the following entries:

  • DotClock clock
        is the dot (pixel) clock rate to be used for the mode.
  • HTimings hdisp hsyncstart hsyncend htotal
        specifies the horizontal timings for the mode.
  • VTimings vdisp vsyncstart vsyncend vtotal
        specifies the vertical timings for the mode.
  • Flags \*q flag \*q ...
        specifies an optional set of mode flags, each of which is a separate string in double quotes.

\*qInterlace\*q indicates that the mode is interlaced.

\*qDoubleScan\*q indicates a mode where each scanline is doubled.

\*q+HSync\*q and

\*q-HSync\*q can be used to select the polarity of the HSync signal.

\*q+VSync\*q and

\*q-VSync\*q can be used to select the polarity of the VSync signal.

\*qComposite\*q can be used to specify composite sync on hardware where this is supported. Additionally, on some hardware,

\*q+CSync\*q and

\*q-CSync\*q may be used to select the composite sync polarity.

  • HSkew hskew
        specifies the number of pixels (towards the right edge of the screen) by which the display enable signal is to be skewed. Not all drivers use this information. This option might become necessary to override the default value supplied by the server (if any). « Roving » horizontal lines indicate this value needs to be increased. If the last few pixels on a scan line appear on the left of the screen, this value should be decreased.
  • VScan vscan
        specifies the number of times each scanline is painted on the screen. Not all drivers use this information. Values less than 1 are treated as 1, which is the default. Generally, the

\*qDoubleScan\*q

Flag mentioned above doubles this value.

  • ModeLine \*q name \*q mode-description
           This entry is a more compact version of the

Mode entry, and it also can be used to specify video modes for the monitor. is a single line format for specifying video modes. In most cases this isn't necessary because the built-in set of VESA standard modes will be sufficient.


       The mode-descriptionis in four sections, the first three of which are mandatory. The first is the dot (pixel) clock. This is a single number specifying the pixel clock rate for the mode in MHz. The second section is a list of four numbers specifying the horizontal timings. These numbers are the hdisp , hsyncstart , hsyncend , and htotalvalues. The third section is a list of four numbers specifying the vertical timings. These numbers are the vdisp , vsyncstart , vsyncend , and vtotalvalues. The final section is a list of flags specifying other characteristics of the mode.

Interlace indicates that the mode is interlaced.

DoubleScan indicates a mode where each scanline is doubled.

+HSync and

-HSync can be used to select the polarity of the HSync signal.

+VSync and

-VSync can be used to select the polarity of the VSync signal.

Composite can be used to specify composite sync on hardware where this is supported. Additionally, on some hardware,

+CSync and

-CSync may be used to select the composite sync polarity. The

HSkew and

VScan options mentioned above in the

Modes entry description can also be used here.

  • Option \*qDPMS\*q \*qbool\*q
           This option controls whether the server should enable the DPMS extension for power management for this screen. The default is to enable the extension.
  • Option \*qSyncOnGreen\*q \*qbool\*q
           This option controls whether the video card should drive the sync signal on the green color pin. Not all cards support this option, and most monitors do not require it. The default is off.
  • Option \*qPrimary\*q \*qbool\*q
           This optional entry specifies that the monitor should be treated as the primary monitor. (RandR 1.2-supporting drivers only)
  • Option \*qPreferredMode\*q \*qstring\*q
           This optional entry specifies a mode to be marked as the preferred initial mode of the monitor. (RandR 1.2-supporting drivers only)
  • Option \*qPosition\*q \*qx y\*q
           This optional entry specifies the position of the monitor within the X screen. (RandR 1.2-supporting drivers only)
  • Option \*qLeftOf\*q \*qoutput\*q
           This optional entry specifies that the monitor should be positioned to the left of the output (not monitor) of the given name. (RandR 1.2-supporting drivers only)
  • Option \*qRightOf\*q \*qoutput\*q
           This optional entry specifies that the monitor should be positioned to the right of the output (not monitor) of the given name. (RandR 1.2-supporting drivers only)
  • Option \*qAbove\*q \*qoutput\*q
           This optional entry specifies that the monitor should be positioned above the output (not monitor) of the given name. (RandR 1.2-supporting drivers only)
  • Option \*qBelow\*q \*qoutput\*q
           This optional entry specifies that the monitor should be positioned below the output (not monitor) of the given name. (RandR 1.2-supporting drivers only)
  • Option \*qEnable\*q \*qbool\*q
           This optional entry specifies whether the monitor should be turned on at startup. By default, the server will attempt to enable all connected monitors. (RandR 1.2-supporting drivers only)
  • Option \*qMinClock\*q \*qfrequency\*q
           This optional entry specifies the minimum dot clock, in kHz, that is supported by the monitor.
  • Option \*qMaxClock\*q \*qfrequency\*q
           This optional entry specifies the maximum dot clock, in kHz, that is supported by the monitor.
  • Option \*qIgnore\*q \*qbool\*q
           This optional entry specifies that the monitor should be ignored entirely, and not reported through RandR. This is useful if the hardware reports the presence of outputs that don't exist. (RandR 1.2-supporting drivers only)
  • Option \*qRotate\*q \*qrotation\*q
           This optional entry specifies the initial rotation of the given monitor. Valid values for rotation are \*qnormal\*q, \*qleft\*q, \*qright\*q, and \*qinverted\*q. (RandR 1.2-supporting drivers only)

13. MODES SECTION

The config file may have multiple

Modes sections, or none. These sections provide a way of defining sets of video modes independently of the

Monitor sections.

Monitor sections may include the definitions provided in these sections by using the

UseModes keyword. In most cases the

Modes sections are not necessary because the built-in set of VESA standard modes will be sufficient.

Modes sections have the following format:


    .nf

Section \*qModes\*q Identifier \*q name \*q entries"..."

EndSection

The

Identifier entry specifies the unique name for this set of mode descriptions. The other entries permitted in

Modes sections are the

Mode and

ModeLine entries that are described above in the

Monitor section.

14. SCREEN SECTION

The config file may have multiple

Screen sections. There must be at least one, for the « screen » being used. A « screen » represents the binding of a graphics device ( Device section) and a monitor ( Monitor section). A

Screen section is considered « active » if it is referenced by an active

ServerLayout section or by the

-screen command line option. If neither of those is present, the first

Screen section found in the config file is considered the active one.

Screen sections have the following format:


    .nf

Section \*qScreen\*q Identifier \*q name \*q Device \*q devid \*q Monitor \*q monid \*q entries"..."SubSection \*qDisplay\*q entries"...

EndSubSection ..."

EndSection

The

Identifier and

Device entries are mandatory. All others are optional.

The

Identifier entry specifies the unique name for this screen. The

Screen section provides information specific to the whole screen, including screen-specific

R Options . In multi-head configurations, there will be multiple active

Screen sections, one for each head. The entries available for this section are:

  • Device \*q device-id \*q
           This mandatory entry specifies the

Device section to be used for this screen. This is what ties a specific graphics card to a screen. The device-idmust match the

Identifier of a

Device section in the config file.

  • Monitor \*q monitor-id \*q
           specifies which monitor description is to be used for this screen. If a

Monitor name is not specified, a default configuration is used. Currently the default configuration may not function as expected on all platforms.

  • VideoAdaptor \*q xv-id \*q
           specifies an optional Xv video adaptor description to be used with this screen.
  • DefaultDepth depth
           specifies which color depth the server should use by default. The

-depth command line option can be used to override this. If neither is specified, the default depth is driver-specific, but in most cases is 8.

  • DefaultFbBpp bpp
           specifies which framebuffer layout to use by default. The

-fbbpp command line option can be used to override this. In most cases the driver will chose the best default value for this. The only case where there is even a choice in this value is for depth 24, where some hardware supports both a packed 24 bit framebuffer layout and a sparse 32 bit framebuffer layout.

Options

       Various

Option flags may be specified in the

Screen section. Some are driver-specific and are described in the driver documentation. Others are driver-independent, and will eventually be described here.

  • Option \*qAccel\*q
           Enables XAA (X Acceleration Architecture), a mechanism that makes video cards' 2D hardware acceleration available to the Xorg server. This option is on by default, but it may be necessary to turn it off if there are bugs in the driver. There are many options to disable specific accelerated operations, listed below. Note that disabling an operation will have no effect if the operation is not accelerated (whether due to lack of support in the hardware or in the driver).
  • Option \*qInitPrimary\*q \*q boolean \*q
           Use the Int10 module to initialize the primary graphics card. Normally, only secondary cards are soft-booted using the Int10 module, as the primary card has already been initialized by the BIOS at boot time. Default: false.
  • Option \*qNoInt10\*q \*q boolean \*q
           Disables the Int10 module, a module that uses the int10 call to the BIOS of the graphics card to initialize it. Default: false.
  • Option \*qNoMTRR\*q
           Disables MTRR (Memory Type Range Register) support, a feature of modern processors which can improve video performance by a factor of up to 2.5. Some hardware has buggy MTRR support, and some video drivers have been known to exhibit problems when MTRR's are used.
  • Option \*qXaaNoCPUToScreenColorExpandFill\*q
           Disables accelerated rectangular expansion blits from source patterns stored in system memory (using a memory-mapped aperture).
  • Option \*qXaaNoColor8x8PatternFillRect\*q
           Disables accelerated fills of a rectangular region with a full-color pattern.
  • Option \*qXaaNoColor8x8PatternFillTrap\*q
           Disables accelerated fills of a trapezoidal region with a full-color pattern.
  • Option \*qXaaNoDashedBresenhamLine\*q
           Disables accelerated dashed Bresenham line draws.
  • Option \*qXaaNoDashedTwoPointLine\*q
           Disables accelerated dashed line draws between two arbitrary points.
  • Option \*qXaaNoImageWriteRect\*q
           Disables accelerated transfers of full-color rectangular patterns from system memory to video memory (using a memory-mapped aperture).
  • Option \*qXaaNoMono8x8PatternFillRect\*q
           Disables accelerated fills of a rectangular region with a monochrome pattern.
  • Option \*qXaaNoMono8x8PatternFillTrap\*q
           Disables accelerated fills of a trapezoidal region with a monochrome pattern.
  • Option \*qXaaNoOffscreenPixmaps\*q
           Disables accelerated draws into pixmaps stored in offscreen video memory.
  • Option \*qXaaNoPixmapCache\*q
           Disables caching of patterns in offscreen video memory.
  • Option \*qXaaNoScanlineCPUToScreenColorExpandFill\*q
           Disables accelerated rectangular expansion blits from source patterns stored in system memory (one scan line at a time).
  • Option \*qXaaNoScanlineImageWriteRect\*q
           Disables accelerated transfers of full-color rectangular patterns from system memory to video memory (one scan line at a time).
  • Option \*qXaaNoScreenToScreenColorExpandFill\*q
           Disables accelerated rectangular expansion blits from source patterns stored in offscreen video memory.
  • Option \*qXaaNoScreenToScreenCopy\*q
           Disables accelerated copies of rectangular regions from one part of video memory to another part of video memory.
  • Option \*qXaaNoSolidBresenhamLine\*q
           Disables accelerated solid Bresenham line draws.
  • Option \*qXaaNoSolidFillRect\*q
           Disables accelerated solid-color fills of rectangles.
  • Option \*qXaaNoSolidFillTrap\*q
           Disables accelerated solid-color fills of Bresenham trapezoids.
  • Option \*qXaaNoSolidHorVertLine\*q
           Disables accelerated solid horizontal and vertical line draws.
  • Option \*qXaaNoSolidTwoPointLine\*q
           Disables accelerated solid line draws between two arbitrary points.

Each

Screen section may optionally contain one or more

Display subsections. Those subsections provide depth/fbbpp specific configuration information, and the one chosen depends on the depth and/or fbbpp that is being used for the screen. The

Display subsection format is described in the section below.

15. DISPLAY SUBSECTION

Each

Screen section may have multiple

Display subsections. The « active »

Display subsection is the first that matches the depth and/or fbbpp values being used, or failing that, the first that has neither a depth or fbbpp value specified. The

Display subsections are optional. When there isn't one that matches the depth and/or fbbpp values being used, all the parameters that can be specified here fall back to their defaults.

Display subsections have the following format:


    .nf

SubSection \*qDisplay\*q Depth depth entries"..."

EndSubSection

  • Depth depth
           This entry specifies what colour depth the

Display subsection is to be used for. This entry is usually specified, but it may be omitted to create a match-all

Display subsection or when wishing to match only against the

FbBpp parameter. The range of depthvalues that are allowed depends on the driver. Most drivers support 8, 15, 16 and 24. Some also support 1 and/or 4, and some may support other values (like 30). Note: depthmeans the number of bits in a pixel that are actually used to determine the pixel colour. 32 is not a valid depthvalue. Most hardware that uses 32 bits per pixel only uses 24 of them to hold the colour information, which means that the colour depth is 24, not 32.

  • FbBpp bpp
           This entry specifies the framebuffer format this

Display subsection is to be used for. This entry is only needed when providing depth 24 configurations that allow a choice between a 24 bpp packed framebuffer format and a 32bpp sparse framebuffer format. In most cases this entry should not be used.

  • Weight red-weight green-weight blue-weight
           This optional entry specifies the relative RGB weighting to be used for a screen is being used at depth 16 for drivers that allow multiple formats. This may also be specified from the command line with the

-weight option (see

R Xorg(1)).

  • Virtual xdim ydim
           This optional entry specifies the virtual screen resolution to be used. xdimmust be a multiple of either 8 or 16 for most drivers, and a multiple of 32 when running in monochrome mode. The given value will be rounded down if this is not the case. Video modes which are too large for the specified virtual size will be rejected. If this entry is not present, the virtual screen resolution will be set to accommodate all the valid video modes given in the

Modes entry. Some drivers/hardware combinations do not support virtual screens. Refer to the appropriate driver-specific documentation for details.

  • ViewPort x0 y0
           This optional entry sets the upper left corner of the initial display. This is only relevant when the virtual screen resolution is different from the resolution of the initial video mode. If this entry is not given, then the initial display will be centered in the virtual display area.
  • Modes \*q mode-name \*q ...
           This optional entry specifies the list of video modes to use. Each mode-namespecified must be in double quotes. They must correspond to those specified or referenced in the appropriate

Monitor section (including implicitly referenced built-in VESA standard modes). The server will delete modes from this list which don't satisfy various requirements. The first valid mode in this list will be the default display mode for startup. The list of valid modes is converted internally into a circular list. It is possible to switch to the next mode with

Ctrl+Alt+Keypad-Plus and to the previous mode with

R Ctrl+Alt+Keypad-Minus . When this entry is omitted, the valid modes referenced by the appropriate

Monitor section will be used. If the

Monitor section contains no modes, then the selection will be taken from the built-in VESA standard modes.

  • Visual \*q visual-name \*q
           This optional entry sets the default root visual type. This may also be specified from the command line (see the

R Xserver(1) man page). The visual types available for depth 8 are (default is

R PseudoColor ):


           .nf

StaticGray

GrayScale

StaticColor

PseudoColor

TrueColor

DirectColor


       The visual type available for the depths 15, 16 and 24 are (default is

R TrueColor ):


    .nf

TrueColor

DirectColor

Not all drivers support

DirectColor at these depths.

The visual types available for the depth 4 are (default is

R StaticColor ):


    .nf

StaticGray

GrayScale

StaticColor

PseudoColor

The visual type available for the depth 1 (monochrome) is

R StaticGray .

  • Black red green blue
           This optional entry allows the « black » colour to be specified. This is only supported at depth 1. The default is black.
  • White red green blue
           This optional entry allows the « white » colour to be specified. This is only supported at depth 1. The default is white.

Options

       Option flags may be specified in the

Display subsections. These may include driver-specific options and driver-independent options. The former are described in the driver-specific documentation. Some of the latter are described above in the section about the

Screen section, and they may also be included here.

16. SERVERLAYOUT SECTION

The config file may have multiple

ServerLayout sections. A « server layout » represents the binding of one or more screens ( Screen sections) and one or more input devices ( InputDevice sections) to form a complete configuration. In multi-head configurations, it also specifies the relative layout of the heads. A

ServerLayout section is considered « active » if it is referenced by the

-layout command line option or by an

Option \*qDefaultServerLayout\*q entry in the

ServerFlags section (the former takes precedence over the latter). If those options are not used, the first

ServerLayout section found in the config file is considered the active one. If no

ServerLayout sections are present, the single active screen and two active (core) input devices are selected as described in the relevant sections above.

ServerLayout sections have the following format:


    .nf

Section \*qServerLayout\*q Identifier \*q name \*q Screen \*q screen-id \*q ..."InputDevice \*q idev-id \*q ..."options"..."

EndSection

Each

ServerLayout section must have an

Identifier entry and at least one

Screen entry.

The

Identifier entry specifies the unique name for this server layout. The

ServerLayout section provides information specific to the whole session, including session-specific

R Options . The

ServerFlags options (described above) may be specified here, and ones given here override those given in the

ServerFlags section.

The entries that may be used in this section are described here.

  • Screen screen-num \*qscreen-id\*q position-information
           One of these entries must be given for each screen being used in a session. The screen-idfield is mandatory, and specifies the

Screen section being referenced. The screen-numfield is optional, and may be used to specify the screen number in multi-head configurations. When this field is omitted, the screens will be numbered in the order that they are listed in. The numbering starts from 0, and must be consecutive. The position-informationfield describes the way multiple screens are positioned. There are a number of different ways that this information can be provided:

  • x y"
  • Absolute x y
        These both specify that the upper left corner's coordinates are ( x , y ). The

Absolute keyword is optional. Some older versions of XFree86 (4.2 and earlier) don't recognise the

Absolute keyword, so it's safest to just specify the coordinates without it.

  • RightOf \*q screen-id \*q
  • LeftOf \*q screen-id \*q
  • Above \*q screen-id \*q
  • Below \*q screen-id \*q
  • Relative \*q screen-id \*q x y
        These give the screen's location relative to another screen. The first four position the screen immediately to the right, left, above or below the other screen. When positioning to the right or left, the top edges are aligned. When positioning above or below, the left edges are aligned. The

Relative form specifies the offset of the screen's origin (upper left corner) relative to the origin of another screen.

  • InputDevice \*q idev-id \*q \*q option \*q ...
           One of these entries should be given for each input device being used in a session. Normally at least two are required, one each for the core pointer and keyboard devices. If either of those is missing, suitable

InputDevice entries are searched for using the method described above in the

INPUTDEVICE section. The idev-idfield is mandatory, and specifies the name of the

InputDevice section being referenced. Multiple optionfields may be specified, each in double quotes. The options permitted here are any that may also be given in the

InputDevice sections. Normally only session-specific input device options would be used here. The most commonly used options are:


           .nf

\*qCorePointer\*q

\*qCoreKeyboard\*q

\*qSendCoreEvents\*q


       and the first two should normally be used to indicate the core pointer and core keyboard devices respectively.

Options

       In addition to the following, any option permitted in the

ServerFlags section may also be specified here. When the same option appears in both places, the value given here overrides the one given in the

ServerFlags section.

  • Option \*qIsolateDevice\*q \*q bus-id \*q
           Restrict device resets to the specified bus-id . See the

BusID option (described in

R above) for the format of the bus-idparameter. This option overrides

R SingleCard , if specified. At present, only PCI devices can be isolated in this manner.

  • Option \*qSingleCard\*q \*q boolean \*q
           As

R IsolateDevice , except that the bus ID of the first device in the layout is used.

Here is an example of a

ServerLayout section for a dual headed configuration with two mice:


    .nf

Section \*qServerLayout\*q

Identifier \*qLayout 1\*q

Screen \*qMGA 1\*q

Screen \*qMGA 2\*q RightOf \*qMGA 1\*q

InputDevice \*qKeyboard 1\*q \*qCoreKeyboard\*q

InputDevice \*qMouse 1\*q \*qCorePointer\*q

InputDevice \*qMouse 2\*q \*qSendCoreEvents\*q

Option \*qBlankTime\*q \*q5\*q

EndSection

17. DRI SECTION

This optional section is used to provide some information for the Direct Rendering Infrastructure. Details about the format of this section can be found in the README.DRI document, which is also available on-line at <http://dri.freedesktop.org/> .

18. VENDOR SECTION

The optional

Vendor section may be used to provide vendor-specific configuration information. Multiple

Vendor sections may be present, and they may contain an

Identifier entry and multiple

Option flags. The data therein is not used in this release.

19. SEE ALSO

General:

R X (7),

R Xserver (1),

R Xorg (1),

R cvt (1),

R gtf (1).

Not all modules or interfaces are available on all platforms.

Display drivers:

R apm (4),

R ati (4),

R chips (4),

R cirrus (4),

R cyrix (4),

R fbdev (4),

R glide (4),

R glint (4),

R i128 (4),

R i740 (4),

R imstt (4),

R intel (4),

R mga (4),

R neomagic (4),

R nv (4),

R openchrome (4),

R r128 (4),

R radeon (4),

R rendition (4),

R savage (4),

R s3virge (4),

R siliconmotion (4),

R sis (4),

R sisusb (4),

R sunbw2 (4),

R suncg14 (4),

R suncg3 (4),

R suncg6 (4),

R sunffb (4),

R sunleo (4),

R suntcx (4),

R tdfx (4),

R trident (4),

R tseng (4),

R vesa (4),

R vmware (4),

R voodoo (4),

R wsfb (4),

R xgi (4),

R xgixp (4).

Input drivers:

R acecad (4),

R calcomp (4),

R citron (4),

R dmc (4),

R dynapro (4),

R elographics (4),

R evdev (4),

R fpit (4),

R js_x (4),

R joystick (4),

R kbd (4),

R magictouch (4),

R microtouch (4),

R mousedrv (4),

R mutouch (4),

R palmax (4),

R penmount (4),

R synaptics (4),

R tek4957 (4),

R ur98 (4),

R vmmouse (4),

R void (4),

R wacom (4).

Other modules and interfaces:

R exa (4),

R fbdevhw (4),

R v4l (4).

20. AUTHORS

This manual page was largely rewritten by David Dawes <> .