Man page 1 : foo2hp2600-wrapper

These are the options used to select the parameters of a print job that are usually controlled on a per job basis.

• -b\0 bits
      Number of bits per plane. 1 or 2. [1].
• -c
      Print in color (else monochrome).
• -d\0 duplex
      Duplex code to send to printer [1].
• -m\0 media
      Media code to send to printer [1].
• -p\0 paper
      Paper size code to send to printer [1].
• -n\0 copies
      Number of copies [1].
• -r\0 xres x yres
      Set device resolution in pixels/inch [1200x600].
• -s\0 source
      Source (Input Slot) code to send to printer [7].
• -t
      Draft mode. Every other pixel is white.
• -2 -3 -4 -5 -6 -8 -9 -10 -12 -14 -15 -16 -18
      Print in N-up. Requires the psutils package.
• -o\0 orient
      Orientation used for N-up.

These are the options used to customize the operation of foo2hp for a particular printer.

• -u\0 xoff x yoff
      Set the offset of the start of the printable region from the upper left corner, in pixels [varies with paper size]. The defaults should work on the 2200DL and 2300DL, and have not been tested on any other printers.
• -l\0 xoff x yoff
      Set the offset of the end of the printable region from the lower right corner, in pixels [varies with paper size]. The defaults should work on the 2200DL and 2300DL, and have not been tested on any other printers.
• -L\0 mask
      Send the logical clipping values from -u/-l in the ZjStream. foo2hp2600-wrapper always runs Ghostscript with the ideal page dimensions, so that the scale of the image is correct, regardless whether or not the printer has unprintable regions. This option is used to move the position of the clipped image back to where it belongs on the page. The default is to send the amount which was clipped by -u and -l, and should be good in most cases.
• -P
      Do not send START_PLANE codes on monochrome output. May be needed by some monochrome-only printers, such as the HP LaserJet 1000.
• -X\0 padlen
      Add extra zero padding to the end of BID segments. The default is 16 bytes. Padding 16 bytes of zeroes is needed for older ZjStream printers, such as the Minolta 2200DL and HP LaserJet 1000, and seems harmless to newer ones, such as the Minolta 2300DL. So the default should be good for all cases.
• -z\0 model
      Model: Model: 0=HP CLJ 1600/2600n; 1=HP CLJ CP1215

These are the options used to control the quality of color output. Color correction is currently a WORK IN PROGRESS.

• -g\0 gsopts
      Additional options to pass to Ghostscript, such as -g« -dDITHERPPI=nnn », etc. This option may appear more than once.
• -G\0 profile.icm
      Convert profile.icm to a Postscript color rendering dictionary (CRD) using foo2zjs-icc2ps and adjust the printer colors by using the Postscript setcolorrendering operator. If profile.icm is none.icm, then prepare for ordering a ICM custom printer profile (i.e. from www.ICCFactory.com).
• -G\0 gamma-file.ps
      Prepend gamma-file.ps to the Postscript input to perform color correction using the setcolortransfer Postscript operator. For example, the file might contain:
  {0.333 exp} {0.333 exp} {0.333 exp} {0.333 exp} setcolortransfer
• -I\0 intent
      Select profile intent from the ICM file. 0=Perceptual, 1=Colorimetric, 2=Saturation, 3=Absolute. Default is 0 (perceptual).

These options are used for debugging foo2hp and its wrapper.

• -S\0 plane
      Output just a single color plane from a color print and print it on the black plane. The default is to output all color planes.
• -D\0 level
      Set Debug level [0].